Talk:Chamfer

This article is written in American English, which has its own spelling conventions (color, defense, traveled) and some terms that are used in it may be different or absent from other varieties of English. According to the relevant style guide, this should not be changed without broad consensus.

Metalworking Low‑importance

	This article is within the scope of WikiProject Metalworking, a collaborative effort to improve the coverage of Metalworking on Wikipedia. If you would like to participate, please visit the project page, where you can join the discussion and see a list of open tasks.MetalworkingWikipedia:WikiProject MetalworkingTemplate:WikiProject MetalworkingMetalworking articles
Low	This article has been rated as Low-importance on the project's importance scale.

Architecture

	Architecture portal This article is within the scope of WikiProject Architecture, a collaborative effort to improve the coverage of Architecture on Wikipedia. If you would like to participate, please visit the project page, where you can join the discussion and see a list of open tasks.ArchitectureWikipedia:WikiProject ArchitectureTemplate:WikiProject ArchitectureArchitecture articles
???	This article has not yet received a rating on the project's importance scale.

Clarification

Should the second "exterior" read "interior? If not, would someone please clarify

Thanks, I fixed it. Kappa 06:35, 15 Jun 2005 (UTC)

chamfer notation on engineering drawings

When a chamfer is annotated on an engineering drawing, does the length correspond to the hypotneuse or the two equal edges of the right triange formed?

The complete answer is actually fairly complex, since it gets into GD&T (Geometric Dimensioning and Tolerancing, [1]). The short answer is that enough information must be shown to unambiguously describe the chamfer. Typically this is done by showing the lengths of the two non-hypotenuse sides of the triangle. Alternately, you could show the length of one such side as well as the angle formed between the chamfer and one of the sides of the object being chamfered. I have never seen a chamfer illustrated using the length of the hypotenuse; I suppose it could be done, but for GD&T reasons I won't get into, it's generally not a good way of doing it. Fasrad 16:48, 26 May 2006 (UTC)[reply]

is a fillet a chamfer?

quoted from article: "Chamfers may be both exterior (cutting off an external angle) and interior (filling in an internal angle). A fillet is the opposite, rounding off an interior corner."

The first sentence says that a fillet is a chamfer, as something that fills in an interior angle can be called a chamfer. The second sentece says that a fillet is the opposite of a chamfer, implying that something that fills in an interior angle is *not* a chamfer. --—Preceding unsigned comment added by 72.17.139.211 (talk • contribs)

It is my opinion that the real difference between a "fillet" and a "chamfer" is that a fillet is curved, while a chamfer is straight. This is consistent with the nomenclature of AutoCAD, and so I will change the text to match my understanding. (Certainly it's ambiguous as it was!)

--jackhmo —Preceding unsigned comment added by Jackhmo (talk • contribs) 17:18, 30 January 2009 (UTC)[reply]

AutoCAD input syntax cannot be taken as any more authoritative than someone's opinion regarding mechanical engineering terms. A fillet eases an inside corner, and may be radiused or blobby, such as a welding bead, less often sharply defined like a chamfer, which eases an outside corner or arris. __Just plain Bill (talk) 23:59, 30 January 2009 (UTC)[reply]

I can't speak to the AutoCAD syntax, because sadly I've never yet had a chance to learn AutoCAD. But I can say that if you ask the guy on the shop floor, a fillet is what eases an inside corner and a chamfer is what eases an outside corner. That is, what Bill said. — ¾-10 00:29, 31 January 2009 (UTC)[reply]

Okay, after further research, it is clear that fillet is only a rounded inside corner, as you said. A rounded OUTside corner is called a "round", although AutoCad still uses the "fillet" command to draw it. I'll fix the wording. Jackhmo (talk) 17:11, 24 February 2009 (UTC)[reply]

How does "chamfer" apply to a punch or rod?

While retreading a stripped bolt hole, the directions said "Punch or rod must have square end (no chamfer)." I am unclear from reading what I have so far how "chamfer" applies in this case. —Preceding unsigned comment added by 66.191.206.3 (talk) 21:26, 7 October 2007 (UTC)[reply]

Proposed merge from Lark's tongue

The following discussion is closed. Please do not modify it. Subsequent comments should be made in a new section. A summary of the conclusions reached follows.

The result was merge. Wizard191 (talk) 00:06, 26 September 2009 (UTC)[reply]

I didn't propose this, but I support it because they are closed related concepts. Wizard191 (talk) 14:13, 25 September 2009 (UTC)[reply]

Strong support The Lark's tongue article will probably never grow beyond the stub that it is now. Since all the info it contains is duplicated here, I would make it redirect to this Chamfer page, if not for the dab hatnote there. Is there a wiki-wizard watching who can help sort that out? __ Just plain Bill (talk) 23:45, 25 September 2009 (UTC)[reply]

The discussion above is closed. Please do not modify it. Subsequent comments should be made on the appropriate discussion page. No further edits should be made to this discussion.

Word origin?

It seems like a rather unusual word - is it named after a specific person or thing? I know this isn't a dictionairy, but it would be nice if the article explained the word's origin... —Preceding unsigned comment added by 131.107.0.85 (talk) 18:38, 9 March 2010 (UTC)[reply]

See http://www.merriam-webster.com/dictionary/chamfer. Apparently, literally, "edge breaking". Cheers, — ¾-10 23:53, 12 March 2010 (UTC)[reply]

Stop chamfer

In Australia these are universally called "Stop chamfers".

The word stop simply indicates the chamfer "stops" before the end of the piece (referred to a "larks tongue" in the article

A chamfer per se goes from one end of the piece to the other.

Oaec 124.182.33.54 (talk) 11:26, 15 December 2015 (UTC)[reply]

I think that's universal. It's the article here that's the problem. It needs to clarify lark's tongues and lamb's tongues for one thing. Andy Dingley (talk) 11:36, 15 December 2015 (UTC)[reply]

What would be the term, if the edge is rounded?

Most of the thing we use in daily life; such as pencil-box, mobile phones, smartphones, Road turns, corners and joints, and such and such; we found in most cases, the corner is blunted; but not exactly a planar chamfer; but a rounded, curved corner.

Is there any term/ wiki page for this structure/method ? RIT RAJARSHI (talk) 16:31, 25 April 2017 (UTC)[reply]

It might be called a bullnose. A woodworker might call a very small chamfer or bullnose "easing the edge" or "breaking" the edge. Just plain Bill (talk) 16:51, 25 April 2017 (UTC)[reply]

Chamfering the curbs

Handicapped access is enabled when chamfering the curbs in urban settings and at highly-accessed sites (e.g. churches and houses of worship, downtown stores, urban curb corners, etc.). Could this be addressed in the article? MaynardClark (talk) 16:03, 28 September 2018 (UTC)[reply]